| 1 | | Front panel | | |
| 2 | | Front panel, top | | |
| 3 | | Side panel, right | | |
| 4 | | Back panel, right | | |
| 5 | | Top panel, right | | |
| 6 | | Back panel, left | | |
| 7 | | Side panel, left | | |
| 8 | | Ash removal door | | |
| 9 | | Top panel, left | | |
| 10 | | Hinge with damper | | |
| 11 | | Location stud M5 | | |
| 12 | | Edge protector | | |
| 13 | | Tie-bar set, basic boiler | | |
| 14 | | Hanging rail set, basic boiler | | |
| 15 | | Tie-bar set, vacuum system | | |
| 16 | | Hanging rail set, vacuum system 18 and 24 kW: with 1 retaining bracket (front) 32 to 48 kW: with 2 retaining brackets (front and rear) | | |
| 17 | | Cable ties with expanding anchor, 210 x 4.7 | | |
| 1 | | Front panel | | |
| 2 | | Front panel, top | | |
| 3 | | Side panel, right | | |
| 4 | | Back panel, right | | |
| 5 | | Side panel, flexible screw conveyor | | |
| 6 | | Top panel, flexible screw conveyor | | |
| 7 | | Tie-bar set, basic boiler | | |
| 8 | | Hanging rail set, basic boiler | | |
| 9 | | Location stud M5 | | |
| 10 | | Edge protector | | |
| 11 | | Cable ties with expanding anchor, 210 x 4.7 | | |
| 1 | | Retaining rings (set) | | |
| 2 | | Fixing kit, mixer and HC1 | | |
| 3 | | Mixer motor | | |
| 4 | | Mixer insert | | |
| 5 | | Mixer handle for DN 15-40 | | |
| 6 | | O-ring for mixer 3+4 (wearing part) | | |
| 7 | | Seal ring 50 x 3 for mixer (wearing part) | | |
| 8 | | Circulation pump Yonos PARA | | |
| 9 | | Ball valve 709 | | |
| 10 | | Gasket set A 32 x 44 x 2 (5 pce) (wearing part) | | |
| 11 | | Gasket set A 32 x 39 x 2 (5 pce) (wearing part) | | |
| 12 | | Connecting cable, boiler circuit pump | | |
| 13 | | Connecting cable, boiler valve | | |
| 14 | | Connecting cable, PWM signal | | |
| 15 | | Thermal insulation, return temperature raising facility | | |
| 16 | | Thermal insulation, pipework | | |
| 17 | | Installation instructions for return temperature raising facility | | |
| 1 | | Brush handle | | |
| 2 | | Cleaning brush (wearing part) | | |
| 3 | | Touch-up spray paint, Vitosilver, 150 ml can | | |
| 4 | | Touch-up paint stick, Vitosilver | | |
| 5 | | Touch-up spray paint, anthracite, 150 ml can | | |
| 6 | | Installation and service instructions for Vitoligno 300-C, 18 - 48 kW | | |
| 7 | | Operating instructions for Vitoligno 300-C, 18 - 48 kW | | |
| 1 | | Programming unit | | |
| 2 | | Retainer housing | | |
| 3 | | High limit safety cut-out | | |
| 4 | | Corrugated hose DN 10 | | |
| 5 | | Oval diaphragm grommet | | |
| 6 | | Grommets | | |
| 7 | | Open side section | | |
| 8 | | Open side section, length 90 mm | | |
| 9 | | Strain relief fittings | | |
| 10 | | PCB KSK2.03 | | |
| 11 | | PCB HKK2.01 | | |
| 12 | | PCB ZPK2.02 | | |
| 13 | | Power supply unit, boiler control unit | | |
| 14 | | Timer charge motor | | |
| 15 | | Jumper set, PCBs | | |
| 16 | | Earthing jumper | | |
| 17 | | Battery: Button cell, type CR2032, 3 V (wearing part) | | |
| 18 | | Microfuses | | |
| 19 | | Plug set KSK low voltage | | |
| 20 | | Plug set KSK 230 V | | |
| 21 | | Plug set HKK low voltage | | |
| 22 | | Plug set HKK 230 V | | |
| 23 | | Plug set ZPK low voltage | | |
| 24 | | Plug set ZPK 230 V | | |
| 25 | | Lambda probe (wearing part) | | |
| 26 | | Connecting cable, Lambda probe | | |
| 27 | | Connecting cable, secondary stepper motor | | |
| 28 | | Connecting cable, primary stepper motor | | |
| 29 | | Connecting cable, grate motor | | |
| 30 | | Connecting cable, grate monitor | | |
| 31 | | Connecting cable, ash removal motor | | |
| 32 | | Connecting cable, ignition element (wearing part) | | |
| 33 | | Connecting cable, ash removal limit switch | | |
| 34 | | Flow temperature sensor | | |
| 35 | | Return temperature sensor | | |
| 36 | | Flue gas temperature sensor | | |
| 37 | | Connecting cable, feed screw conveyor motor | | |
| 38 | | Connecting lead, pellet sensor | | |
| 39 | | Temperature sensor Pt1000 | | |
| 40 | | Outside temperature sensor | | |
| 41 | | Connecting cable, cleaning limit switch | | |
| 42 | | Earth cable | | |
| 43 | | Spacers (10 pce) | | |
| 44 | | Richco spacers (4 pce) | | |
| 45 | | Spacer set | | |
| 1 | | Pellet hopper gasket (wearing part) | | |
| 2 | | Toggle fastener | | |
| 3 | | Pellet sensor | | |
| 4 | | Suction turbine | | |
| 5 | | Spiral hose 50 x 0.8 | | |
| 6 | | Fixing kit, spiral hose | | |
| 7 | | O-ring 30 x 3 (wearing part) | | |
| 8 | | Connecting cable, vacuum module incl. filter | | |
| 9 | | Union flange gasket (wearing part) | | |
| 10 | | Rotary lock valve gasket (wearing part) | | |
| 1 | | Rotary adjustment | | |
| 2 | | Rotary unit | | |
| 3 | | Geared motor | | |
| 4 | | Flexible spiral 3 m | | |
| 5 | | Flexible spiral 4 m | | |
| 6 | | Motor shaft | | |
| 7 | | Washers, rotary unit | | |
| 8 | | Hose 3 m | | |
| 9 | | Hose 4 m | | |
| 10 | | Hose support | | |
| 11 | | Pellet sensor | | |
| 12 | | Spiral fixing tab | | |
| 13 | | Spiral shaft | | |
| 14 | | Shaft seal ring 28 x 40 x 6 (wearing part) | | |
| 15 | | Hose clip | | |
| 16 | | Bearing retainer | | |
| 17 | | Inspection cover, rotating-pivoting adjustment | | |
| 18 | | Inspection cover gasket (wearing part) | | |
| 19 | | Gasket for rotary adjuster (wearing part) | | |
| 20 | | Connecting cable, room discharge motor | | |
| 1 | | Charging unit, complete | | |
| 2 | | Screw conveyor unit, feed | | |
| 3 | | Chain wheel set, feed (wearing part) | | |
| 4 | | Gasket set, feed (wearing part) | | |
| 5 | | Friction bearings and fixings (wearing part) | | |
| 6 | | Offset geared motor | | |
| 7 | | Support screw | | |
| 1 | | Ash box | | |
| 2 | | Extendible handle | | |
| 3 | | Packing 12 x 12 (wearing part) | | |
| 4 | | Toggle fastener | | |
| 5 | | Tensioning toggle | | |
| 6 | | Recessed handle | | |
| 7 | | Castor set | | |
| 8 | | Rubber feet set (wearing part) | | |
| 1 | | Thermal insulation mat, inspection cover | | |
| 2 | | Upper thermal insulation mat | | |
| 3 | | Thermal insulation set | | |
| 1 | | Fan casing | | |
| 2 | | Radial fan (wearing part) | | |
| 3 | | Insulation connector | | |
| 4 | | Sensor well, flue gas temperature sensor | | |
| 5 | | Gasket, flue gas fan (wearing part) | | |
| 6 | | Inspection cover, top | | |
| 7 | | Packing 16 x 12 (wearing part) | | |
| 8 | | Thermal insulation block (wearing part) | | |
| 9 | | Sensor well 1/2" di=6.5 | | |
| 10 | | Separating plate, flue gas box (wearing part) | | |
| 11 | | Spring for cables | | |
| 1 | | Fan casing | | |
| 2 | | Radial fan (wearing part) | | |
| 3 | | Insulation connector | | |
| 4 | | Sensor well, flue gas temperature sensor | | |
| 5 | | Gasket, flue gas fan (wearing part) | | |
| 6 | | Inspection cover, top | | |
| 7 | | Packing 16 x 12 (wearing part) | | |
| 8 | | Thermal insulation block (wearing part) | | |
| 9 | | Sensor well 1/2" di=6.5 | | |
| 10 | | Separating plate, flue gas box (wearing part) | | |
| 11 | | Spring for cables | | |
| 12 | | Insulation brick (wearing part) | | |
| 1 | | Combustion chamber brick insert (wearing part) | | |
| 2 | | Combustion chamber, top brick (wearing part) | | |
| 3 | | Combustion chamber, centre brick (wearing part) | | |
| 4 | | Combustion chamber, bottom brick (wearing part) | | |
| 5 | | Round gasket (wearing part) | | |
| 6 | | Gasket for grate support panel (wearing part) | | |
| 7 | | Finned grate (wearing part) | | |
| 8 | | Spacer bush set | | |
| 9 | | Combustion chamber floor gasket (wearing part) | | |
| 1 | | Stepper motor | | |
| 2 | | Drive unit, air damper | | |
| 3 | | Packing GF 9 x 7 L=2000 (wearing part) | | |
| 4 | | Synchronous motor | | |
| 5 | | Microswitch 30 V 5 A | | |
| 6 | | Drive, finned grate | | |
| 7 | | Grate drive gasket (wearing part) | | |
| 8 | | Chain set, ash removal drive unit (wearing part) | | |
| 9 | | Bearing set (wearing part) | | |
| 10 | | Gasket for ash removal drive unit (wearing part) | | |
| 11 | | Insulating stud | | |
| 1 | | Combustion chamber door | | |
| 2 | | Thermal insulation block, front (wearing part) | | |
| 3 | | Packing 16 x 12 (wearing part) | | |
| 4 | | Thermal insulation block, door insert (wearing part) | | |
| 5 | | Ignition pipe unit | | |
| 6 | | Gasket set, ignition pipe unit (wearing part) | | |
| 7 | | Ignition element (wearing part) | | |
| 8 | | Inspection cover gasket (wearing part) | | |
| 9 | | Compression spring set | | |
| 1 | | Turbulator (wearing part) | | |
| 2 | | Cleaning rocker | | |
| 3 | | Flanged bush 18 x 30 (wearing part) | | |
| 4 | | Drive unit, cleaning rocker | | |
| 5 | | Ash trough, rear | | |
| 6 | | Ash trough, grate | | |
| 7 | | Top plate, grate ash trough | | |
| 8 | | Screw conveyor | | |
| 9 | | Inspection cover, ash removal | | |
| 10 | | Gasket set, ash removal cover (wearing part) | | |
| 11 | | Packing 16 x 12 (wearing part) | | |
| 12 | | Adjustable foot | | |
